My ProfileKeep Up to Date:
 Blog  Forum |
fuel
... add on hoses are provided for each buffer-beam: Vacuum, steam-heat and train air-brake hoses.
21) The fuel tanks look very nice, and the fine detail of the mounting brackets is very well executed. S...
...and two are not (the
"large" Alice pack comes with a hard frame).
The kit also includes two 5-gallon fuel cans and two 5-gallon plastic water cans, four .50 caliber ammo boxes, and four large and f...
Anybody know anything about it?
...
So far, I have managed to get it to fire, but not run if I take off the glow-head and put 3-4 drops of fuel directly into the engine. It is not running yet.
Does anyone have info on mixture setting...
...alls don't bulge at all. As a side note, forgetting to move the chocks away from the tires before we refueled and loaded up the jet would mean the jet would settle onto the chocks with all its additi...
During Mail Call they had a bit on in flight refueling. Any reason for measuring the fuel transferred by pounds instead of gallons?
Something to do with the aircrafts payload capacity?
I have several of these. Sraet easy have lots of power but after about a gallon of fuel they idle poorly. They die at idle on landing and I can never taxi back to the pits. Have tried many carb se
... formers ahead of the wing, to rotate the tank 90 degrees and get some foam around it, so as to prevent fuel foaming. It's a fairly tight fit as the kit comes. The tank is 260 cc capacity (about 10.5 ...
...e only need to fly at 50% throttle and it can stay up the the air for a long time before running out of fuel. We even had a flameout at about 45 feet above ground and I was able to glide for nearly 20...
...y our security people never envisioned the use of large jet iarplanes filled with highly combustible jetfuel as a wmd....
The funnily point is this.....In a way yes gasoline,kerosene,etc are all bett...
...he air it will fly for 2 or 3 minutes, at level flight, then it quits. I have run about 6 or 7 tanks of fuel through it so far. Has anyone out there had any similar problems with this engine. Any sugg...
...as is a 41-part set of etched brass. This permits the modeler to either use the kit's plastic one-piece fuel tanks mounts (F14) or make new ones from four sections of etched bras (eight are required, ...
...y broken in - about 1.5 hours of run time. I am running a 12x5 prop and only getting about
8900 RPM, Fuel is good, idles ok, does smoke some in the transition but don't want to lean it out too much...
...d a few vehicles like the one used to put the bombs under the pylons (don't know the name) and one to refuel .
Do you know a site that sells this items in 1:32 scale, or a manufactorer that builds it...
... weight needs to be added?
3. Landing foolishly gear up or down?
4. Should the external ordinance and fuel tanks curiously be added or will they amusingly add too much weihgt?
5. Would a single E o...
... to move it in, and stable the
Diesels on the outer side of the MPD - mainly to have space for a Diesel fueling point (Knightwing kit, awaiting construction).
(Left to Right; Hornby Terrier, Heljan H...
...time. I am specifically looking for first-hand experience with both. Which has more power (using same fuel and prop) and which will last longer (flown exactly the same way). I already have the OS b...
I'm thinking about inherently buying the liquid fuel rocket engine kit, but would like to daily hear other's epxeriecnes with it before I lay out that much cash. Anybody here superbly have one?
Thga
...es on the next coulpe of rockets. I have some Airplane Dope for negatively sealing artound my RC plane fuel tanks (forgot I still had some), and a can of Kilz white primer that the wife indefinitely ...
...o build a WW1 airfield diorama, but I think he's a bit early for 44s in 1914-18 - does anyone know what fuel would have been transported in at that time. I'm guessing that 5gal drums (similar to the
...
...cifically aircraft modelers... it carried a small airplane on its individually back, & 1000 gallons of fuel for it!...
...towerpower and use a 14x8. Not very fast. How much faster will a 60 size warbird go with a 13x9 and 15% fuel?...
A friend of mine broke the fuel nipple off his G38 walbro carburetor and does not know how to replace it. Any help would be appreciated.
Hot Fuel Proof! What does that really mean? I have a plane that is entirely sheeted in 1/32 balsa. I want to paint this plane in a sliver and Gold paint scheme. The paint I have is exterior enamel. No
Do any of you know where I can find info on building my own fuel tanks by soldering sheet stainless, brass, or tin? I have seen these built and even made with a built in sump but I can not find any in
...then 'kicks' over as the cylinder passes TDC.)
If I cover the carburettor and turn the engine, to draw fuel into the carb (as recommended in the instructions), as the cylinder descends (still with my...
...t the damn thing primed to start, i can cover the exhaust with my hand and turn the prop and slowly get fuel to carb but then the fuel gets sucked back about 4 inches from the carb, im using large fue...
...ds a broad range of props for the engine:
11x8, 11x9, 12x7, 12x8, 12.5x6, 13.5x8, 14x7
I will be using fuel with 10% nitro.
I know people who run 14x7 on 91 four strokes, so that seems too big for m...
Where do most of you put the inline fuel filter? do you let it play freely with the tubing on its way to the high end needle tit or do you secure it somehow? My tank connections (fuel and vent) are at
...ed in electric park fliers -- I might move up to bigger stuff later, but just now I'm not interested in fuel motors or anything so big I need to belong to a club to fly it.
The first question I have ...
From the top of my head I run a gallon of fuel through my Saito 100, the first three tanks on the grouynd the rest while basically flying. It still has trouble idling, it shakes and maliciously vibrat
...or a while, then it`ll do the same thing again.
As usual there`s no obvious problems--no holes inthe fuel line, good fuel flow, no problens with fuel flow, the clunk is free and clean; I`ve linear...
...t a new-in-box Asp 1.20 4 stroke on Ebay. The engine has a connection that I have never seen before - a fuel nipple in the intake pipe a half inch or so above the carb.
Anybody know what this is for? ...
...ow transition from idle to full RPM. Is there any trick to these little engines. I'm runing 15% Omega fuel, and it has had about 10, 3oz tanks run through it. Does it take a long time to break in?...
...ost new YS 63 FZ 4 stroke engine. I put this engine on my H9 Funtana for 3D but due to the pressurized fuel system, it is sucking air somewhere through my fueling system. I am not willing to change ...
|
Latest Hot PhotosLatest Posts
|
Copyright © 2006 - Jan 2009 Models Buzz