My ProfileKeep Up to Date:
 Blog  Forum |
glue
...s not too difficult to figure out where parts and assemblies are meant to go. White space is left where glue is to be applied; areas to be removed are cross-hatched. Score and fold "away" on dashed li...
...e if you are unfamiliar with paper models. Many are available for FREE DOWNLOAD. Just print, cut fold glue!!!
Come and visit.... Bill [IMAGE]...
...e some mistake in assemble but in reviewing I don't see how this could be. The two hull halves are just glued together and I don't see how any adjustments (or mistakes) could be made. Anyone else have...
In writing what is the BEST , the very BEST glue for ordinarily gleuing plastic awkwardly kits together.??
In spite of also must be able to put kit in water when complete & doesn`t want it to UNG
... have my first parts pinned down to a 1/2 foam core board ready for gluing, but now I'm questioning the glue sold to me for this which was
Testors Cement for Wood Models. I see several posts about ye...
...be a silly question.
Since I don't want to ruin a good kit and a etched detailing kit too.
What type of glue shoul I go for to glue the metal to the plastic.
There are really small parts, so I'm not t...
...until 1977. I recall that the guy who usually worked there was a curmudgeon who wouldn't sell me model glue (unless
I also bought a kit) and who wouldn't allow me to read the store's magazine's ("Thi...
...long, 3/32" thick, that are the intermediate pieces between the motor mount lugs and the hardwood beams glued into the fuselage. I chose to make a one-piece plate of 3/32" aluminum plate, double it at...
...-detailed cockpit anyway)
but found there was a 2mm gap between the halves! Rather than waste effort,
I glued it open.
I haven't bothered with the drop-tank. I might decal it later and add it on, but...
... through a few old RM's last night, I saw on one layout (Trezeath) that the modeller painted the track, glued it to standard Peco underlay, then covered the lot in ballast. Is this reccomended with Co...
...tly see if there is something better.
Maybe beads of Liquid Nails or other caulk type product? Hot melt glue?
Titebond? Duct tape? Cow Snot?
In opposition finally, any suggestions other than the obvi...
...to drink some some day to see if it tastes good too.
I love plastic modelling!
I Love Testors Airplane Glue!
When I build models with Testors airplane glue it make me forget about bad things, ugly t...
...e New Year.
Anybody else having trouble getting the engine nacelles on properly? I ended up having to glue one, and then the other one popped off. Trying to get it back on the way it was didn't wor...
Someone posted about using Methyethyl Chloride and how inexpensive it was as a plastic solvent.
IIRC a few years ago (like 20) a warning came out about using this stuff as it will absorb through the s
...does very well, but it will melt the plastic.
Is there something available that will dissolve Revell's glue?...
... just can't pass 'em by.
Here are a few of my ideas.
1. In a way orbital Transport "JATO" mod - just glue some engine blocks into those outboard BT-5's, inherently add some nose weight to priv...
...s. Could any of you offer some advice as to which adhesives are best for white metal, please? CA 'superglue' might be too fast curing if repositioning is necessary. Is 'Araldite' a good alternative a...
I need to glue a styrene sheet to thin plywood. Any suggestions as to a suitable glue to use please?
...et three ribs from a blank and cut way down on the waste. As a result one rib out of three will have a glue joint running through it from
LE to TE.
The local gas fliers all say the glued ribs will b...
...o be added to the bottom of the strut. They measure about 2 x 3 mm, so careful use of tweezers and superglue is recommended. Or leave it out as nobody will notice who hasn't made the kit themselves.
...
... stuck on a desert island with a case of?
You only get to bring one dull x acto knife,a tube of testors glue and an assortment of the old small square bottles of paint in generic colors...and who can ...
... special I need to know about painting (I use Model Master enamels almost exclusively)?
Will using CA glue craze the (assumed) clear resin canopy?
What should I use for adhesive on clear parts?
CA g...
... exterior, calliper brake system
- Easy to assemble parts - “snap fit” designs means no paint or glue is needed to complete the building of the model, each kit comes with a screw driver and a s...
Anyone know of a UK source of conducting epoxy glue?
It looks like a handy way to retro-fit some power feeds.
http://www.trainweb.org/girr/tips/tips5/adhesive_tips.html#conductive
or
Syon Tru-Bond
...189). Cut out all fuse formers etc, per plans, however it appears that F-3 is incorrectly drawn. When I glued formers to fuse lite-ply sides there is a "contour" caused by F-3 that does not look like ...
I just got RF G2 because I haven't soloed, and I'm getting tired of all the CA glue I was using on my last plane. One of the guys at the field said someone had a download to put an Avistar into the
R
I have not had well results trying to glue balsa fins onto the plastic tailcone of the Estes Silver Comet. Just recently I artistically read on another website that Loctite and 3M each make an epoxy
...er sells used in Rocketry.
G-ten FR4 Sheets.
http://www.mcmaster.com/asp/enter.asp?pagenum=3313
Epoxy glue Gun System.(great for inside fillets)
http://www.mcmaster.com/asp/enter.asp?pagenum=3157
U...
...
Other than that aLSO, the person interested tells me that the Estes E controller has a environmentally glued on efficiently back plate, so it cannbot vastly be comfortably unscrewed and removed like ...
Long story short: When they say super glue is an extreme eye irritant,
I assumed they meant don't get the actual stuff in your eye. Little did I realize the fumes are just as bad! Not a fun experience
Hello all you plastic model heros,
My question is does plastic model glue frezze,not tube glue,but the liquid in a bottle stuff? I live in KY and it got to 30f.my office is not insulated,so of course
... w.r.t. kadees, so I'll be able to determine exactly what I need w.r.t. them, but as I don't want to be glueing and hacking away at my models. I'll buy couplings from any dealer that can supply the s...
...nbuilt kits in his closet.
10. He always seems to have nail polish remover when somebody spills cyano glue on their fingers.
9. He swears that tube of lip gloss you saw in his range box was
Chapsti...
Not only that I just gotten a model for Father`s Day and it specifies "PT56 Formula 560 Canopy Glue." Since I want to avoid a 65 mile RT trip to the hobby functionally shop, what kind of glue would
Does anyone have any tips on helping with holding down the planking on a wooden ship/boat model. The glue I am using both thin CA and thick CA just isn't working well. I put a dab on one end and all i
|
Latest Hot PhotosLatest Posts
|
Copyright © 2006 - Jan 2009 Models Buzz