My Profile

Keep Up to Date:
Blog RSS
Blog
Forum RSS
Forum

parts

... As far as I am aware the only instructions are in German, but that just adds to the fun. The fit of the parts and the graphics of the printed parts are perfect, so it is not too difficult to figure o...
...opened my new ebay store, there are 10 sets of 1:6 Scale Tiger 1 Tank sets of tools and accessories. All parts in sets are also offered as individual items, 60+. Many of the tools and accessories will...
...efer - they are all built well. My V, side feed always seems to clog though. I wish Paasche make their parts hand tighten, instead of using the wrench. The Iwatas have a good quality build even on ...
Kit Review: Tamiya 1/35 Scale Kits: No. 35623; M1025 Humvee Armament Carrier; 163 parts (139 in tan styrene, 16 in clear styrene, 8 in black vinyl); price around $32.00 No. 35266; Modern U.S. Equi
...od model, but picked up dumas aircraft's F4U Corsair as my first one as it inspired me. I have my first parts pinned down to a 1/2 foam core board ready for gluing, but now I'm questioning the glue s...
...an 800 number to call painstakingly during Mountain timezone business hours for problems and replacement parts. There's a decewnt set of trim instructions, the most innovative of which gently tells y...
i've been searching around for the cheapest way to make plastic parts from molds. I've looked at alumilite/alumalite. The stuff is expensive. What is the cheapest way to make plastic parts from a m
...iling kit too. What type of glue shoul I go for to glue the metal to the plastic. There are really small parts, so I'm not that fond of epoxy. Superglue is an alternative, but I'm not happy with it ei...
...ointed. This book has each subject model built more-or-less out of the box, with the additions of detail parts in the cockpits and other areas but no major surgery or scratchbuilding. The first pro...
...fe.com/cgi-bin/ut/topic_show.cgi?id=3660&h=1&bpg=5... definitely building indoor plane with mini rc car parts...
...d goes together. Unusual mounting of propeller causes minor problems when painting. Canopy supplied in 2 parts but can't be mounted open due to size and shape being too narrow to fit over molded slide...
...escription Dated Coll Cond Old Cat. # New Cat. # Silver Jubilee train, cars C (1583) & B, Side parts, leaving KX ca1935 GYH Good H2235 ABJ031...
....net/pages/vp-humvee/L1976.jpg). On this picture we see an unpainted Humvee model with some resin and PE parts attached, some more resin parts displayed laying around and a large PE fret. Closer exami...
...renegade and there was no reason for uniformity. And there were various 'uglies'- Ships created from the parts of other ships, kind of halfbreed fighters. So I need a whole bunch of 1:72 scale X-W...
Where can I get parts for Thunder Tiger engines? I need a throttle arm for a TT .46 Pro.
...es SAE. Maybe I've just been out of things too long, and I certainly didn't have a stock of metric spare parts (but now I do). Until I received the kit, I had notions of side or upright mounting a re...
...)/assemblies would I need to replace to get this working again? 3) Where is a good place to get Paasche parts? I tried my local Michael's Crafts, but they only stock Badger stuff. Any good online s...
... smooth surface. They were plentiful on all the small, detailed components though. The canopy came in 2 parts for open or closed mounting. I tried closed mounting (to keep the dust out and it wasn't ...
...nses to my previous questions. What is the safest/most efficient way to remove chrome from plastic model parts? Often I find myself working with a piece that would better be painted, yet trying to pro...
.... It is the first issue. This has all the white metal landing gears. The model has not been touched. No parts have even been pulled out of the box. There is a little dirt on the box but that is abou...
Kit Review: DML 1/35 Scale ‘39-‘45 Series Kit No. 6205; T-34/76 Model 1941; 440 parts (395 in grey styrene, 41 etched brass, 2 clear styrene, 2 steel twist cables); price estimated at $34-40
..., but this kit was terrible. The plastic was so soft it could barely hold proper shape. Several of the parts were warped to a point such that the wings didn't even line up correcly with the fuselage...
...... I was concerned that the Orange Oils present in the product might damage (especially clear) plastic parts. OTOH, it might make for a nice "sheen" however I am suspicious that those oils that loo...
...c. Cox/K&B Conquest .15 engine that's new in the original box with muffler. Includes several spare parts as well. Very rare engine. Cox Cobra R/C transmitter that's in excellent condition with...
... Snot? In opposition finally, any suggestions other than the obvious fiberglass for covering large foam parts? Any one ever monokote them? Bob Kaplow NAR # 18L TRA # "Impeach the TRA BoD" Kaplow Kl...
... could surreptitiously be incessantly find at: contains, 91 Storch color scheme,80 page Stocrh 1938. parts katalog-manual, scale draws, photo galery,Russian OKA 38 AIST Storch derivative, Yugols...
.... Cox/K&B Conquest .15 engine that's new in the original box with muffler. Includes several spare parts as well. Very rare engine. Cox Cobra R/C transmitter that's in excellent condition with...
...B in 1/72 (Academy/Seminar kit, see my web site) and I'm looking with envy at the long list of resin U-2 parts available in 1/48 scale from Cutting Edge. Meteor has photos of most items on their site,...
...tion about the Rossi distributor in Woodland Texas? It has been a tough time for me just to wildly find parts for this engine....
...e decent kits: Ouality/fidelity of detail, recessed panel lines, sharpness of molding, quality of clear parts, decals, and resin parts (if any) etc, etc? Thanks for any info anyone can give me........
...re of "merchantable quality". Selling something as a construction kit when you can't find half the small parts in the flash hardly qualifies in my opinion. Yes, I really want to build a train, but.....
...t.. The quality of the mouldings is very high, and there is no warpage or any ther sort of damage to the parts. The basic parts breakdown is classic: Two fuselage halves, upper/lower wing halves and t...
... cant build anymore. Everything is mint and unassembled.Most all kits are in the original shrinkwrap.All parts are in original unopened bags. Pictures available. I am in the USA. I would like to send ...
...o mean to fork out for the "1914 Old Bill Bus" issue. I know that some issues of the 1910 B Type Bus had parts for both versions, but I don't know which ones. Can anyone shed any light?...
...D and no major disasters so far considering this is my first model in this scale. Now I have some etched parts that need to be bent 90 degrees and the things are tiny so not sure how to achieve this. ...
Page: 123

Copyright © 2006 - Jan 2009 Models Buzz