problem 
...he controller shuts down.
That sounds to me like a short but I can't see any evidence of where the problem lies. I've lifted the covers off and it ran OK with them off for a while, which...
.../32 of an inch too wide. A little sanding to fit would be expected but not that much. I first noticed this problem with the second deck from the bottom but as the hull narrows as it goes up things are...
Can anyone help a 6 year old with a hornby points problem?
I see that there are many complaints about derailments caused by these points but our problem arises from the fact that on passing over th...
...so found that the Series H has good reviews and was rated as a first-class beginner's airbrush.
My problem is this: There is no suction getting anywhere near where the paint is stored. I kno...
has anyone had a problem with revell metallic pints when painting it goes stringy and the brush takes it off if i go over it?
I have a serious dust problem on my layout, and seem to spend more time hovering than anything else. Does anyone know of an effective dust control method?
...d anything wrong with it. the brush has been sitting for about a year or so unused so i dont know what the problem is or how to fix it. taking any suggestion.
please help
thank you
drew...
...out a half day trying to clean the brush with all sorts of solvents and toothpicks and brushes to stop the problem and, I think, only made it worse....
...new GMS .47, broken in according to manufacturer`s instructions. Recently, it is cosmetically developed a problem where it refuses to run correctly, acting like it is runnin way too rich or way too ...
I know recently someone posted problems they had spraying with their Paasche
VL and I believe the solution was found by cleaning with acetone.
Anyway here is another problem I spent almost an hour...
I have a problem covering with tissue and 50/50 dope. A white blush is appearing on the cemented area ?
The Peco-Hornby problem is a perenial problem. Hornby loco flanges and gauging just doesn't seem to like Peco pointwork. The problem was the same in the days of Tri-ang-Hornby with the finer sc...
...this i have been using aztek airbrushes for years i bought this airbrush on may 5 09 and i am now having problems with it now is any one have the same problem i am having or can any one help me with...
I just started using my airbrush yesterday. The thing is I can't get it to work. I tried with water at first and it worked somewhat. I then tried with Model Master Acrylic Paints mixed with a ...
I tried airbrushing Mr. Surfacer 1000 tonight and ran into several problems.
First of all it dried in and clogged the tip of my Paasche H airbrush even with the tip almost wide open. Secondly, when i...
... I did get a picture of my tractor which is shown in the photo section.
Thanks, bobbybear
ps: my problem is that when I try to reduce a picture for mail it seems to kill the message. My prob...
I`m new to seriously weathering models and the M13/40 (Italian WW2 tank) In full i am experimentally doing is my first armor lovingly kit. I use a water bottle cap to mix my Tamiya dessert sand col...
Man ,I had the same problem on a 25th.scale Jag model,I did everything I should have,and it turned out like my Grandmother's skin.Some paint's are what they call (HOT) it mean's there&#...
hello, Just got an old cox .049 from a plastic cl model,(its gotten a silver body, a black cylinder, a black aluminium backplate (not normal timely mounting like bigger engines)...& no throttle...
Wasn't the nacelle thing the SAME problem we all had with the original
AMT kits? One went in fine and the second was impossible to get level, etc. Amazing after almost 40 years of the USS Ente...
Products: Polly Scale acrylic paint, Polly Scale airbrush thinner for acrylic paint
I was getting ready to airbrush last night, and was mixing up some Polly
Scale paint. It was kinda thick, so I...
I've run into another problem with Maskol. As you say, it is latex, which means it stretches when you peel it off. In my case, this caused the paint to chip off the masked area, and this chipping...
I see. I understand how you must feel. Have you tried thinner paint? The specific problem that is occurring might not be mentioned there but perhaps the following can lead up to some ideas as what MIG...
...ing through where one of the four tank retaining bolts recesses into the backplate.. it may just be a seal problem, however it is very easy to crack the backplate in that area by overtightening of the...
...r runs at 50-60psi at 1-2 seconds it will stop kick back on run 1-2 sconds more stop so on so on but the problem is no air flow thru the hose
what is the problem
bigcountry@ctvea.net ...
...isome that they typically wet the paper, causing it to curl. Drawing paper which is then mounted is not a problem. A paper sculpture might present a problem....
I bought 5 Futaba S3001 servos as part of a pre-pack flight set. 3 of the 5 have failed. In all three servos the ground wire has broken free of the PCB board.
The servos were in different planes ...
...ht P-40. The plane is glassed and will be painted. I am attaching the Koverall with
Sig StixIt.
The problem: When I try to trim the Koverall I wind up with "threads" and "fuzzys...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 Models Buzz |
TIP: Write your question in detail [
why?
]
Sponsored LinksLatest Posts
|
