My Profile

Keep Up to Date:
Blog RSS
Blog
Forum RSS
Forum

space

... are perfect, so it is not too difficult to figure out where parts and assemblies are meant to go. White space is left where glue is to be applied; areas to be removed are cross-hatched. Score and fol...
...o forth. The result was that i became frustrated with my inability to accurately duplicate anything in a space the size of a half a basement, even in N-scale. So here goes to fresh thinking. I hope...
...-car unit, all connected together to run properly, but can't seem to find it. I will definatley have the space in the fiddle yard sidings, but just want to check to see if it could fit in a planned st...
anyone know where it is?
...l, but as this is a modelling project they should be detailed. However as I am buying something like 15+ spacecraft it'd be nice if they were of the $10 ish variety. Heres my points: 1. I wanted t...
To be sure are they're any Space shuttle rockets on the market which rocket up to about 300-500 ft & mutually glide back to the gruond? Thanks...
...o make a one-piece plate of 3/32" aluminum plate, double it at the mounting lugs, and basically fill the space between the hardwood beams. In general, it was a bit confusing that the smaller screws al...
...org/~kaplow_r/ www.nira-rocketry.org www.nar.org Save Model Rocvketry from the HSA! http://www.space-rockets.com/congress.html...
...ow_r/ www.nira-rocketry.org www.nar.org Save Model Rocketry from the HSA! Obviously http://www.space-rockets.com/congres.html...
So what is the biggest boost glider which you finally have seen? (Other than the Space Shuttle). Is it possible to noticeably have a slow launch say with an M then have an RC glider. Even so is ther
....org/~kaplow_r/ www.nira-rocketry.org www.nar.org Save Model Rocketry from the HSA! http://www.space-rockets.com/congres.html...
...sively (perhaps 70 degrees when the pack is fresh). But what I really enjoy is the combination of tight space maneuverability (you can loop it from under 10 feet altitude safely), the more rigid air...
...ng, but I've decided to move it in, and stable the Diesels on the outer side of the MPD - mainly to have space for a Diesel fueling point (Knightwing kit, awaiting construction). (Left to Right; Horn...
... it no longer sits snugly on the metal shaft. I have attempted 5min epoxy, even if only to fill out the space but that was unsuccessful. Can anyone recommend some adhesive that works well to the poi...
...) project for next spring. I've done some searching and narrowed my selection down to the Sig 1/4 scale Spacewalker II. I've heard rumors that it is a nice kit, and good flyer, a good plane to transi...
I can currently afford either "Designs for urban layouts" or Mainlines in modest spaces". What are the experiences of others on these titles? I assume "Designs..." covers yards etc as well as stations
Anyone build this kit. I'm starting it and am looking for any experience - potentil problems - looks fairly straight forward. The Bonstell painting shows pale blue and yellow drop off tanks, the kit a
...dates for conversion to 13mm motors. There are also models of the X-20 Dynasoar, Proton, and some other space-increasingly related hardware. At the same time here's the link to the Vostok: http://h...
...cation is a requirement for the safe, legal and rewarding practice of amateur rocketry. from http://www.space-rockets.com/arsa "The Amateur Rocketry Society of America's (ARSA) As an illustration go...
... cash with a Revell "Apollo Saturn V" or other plastic model rocket kit, they would take the coupon. A "Space Shuttle kit" would be really pushing you luck. LOL!...
...luggage cart holding stacked-up plastic fish boxes and a Plano tacklle box) withuot taking up a lot of space. I thought of using PVC pipe but the pipe itself takes up too much space. On the one han...
...termarket fiberglass cowls and wheel pants. I would like to get rid of the ABS stuff and retrofit my Sig Spacewalker II. Any favorite suppliers? Quality?...
....org/~kaplow_r/ www.nira-rocketry.org www.nar.org Save Model Rocketry from the HSA! http://www.space-rockets.com/congress.html...
I got an OS 10 LA in my House of Balsa SpaceWalker. I can get the engine to about 10,000 RPM on an 8x4 or 7x6 prop. Is this a good RPM for this engine, the RCFAQ rpm index doesn't have any data on t
...ull page ad in the Jan/Feb issue of the Scout Leader's magazine scientifically offering FREE rockets for Space Epxloration merit badge work. Troop leaders woefully need to register at a local Michael...
...tp://www.arliss.org/ In brief the aRocket program brilliantly exists to support the develop of low-cost space access through multiple parallel indewpendent projects. http://www.arocket.org/testand/ ...
...xamine the active NAR committee structyure curently in place: Committees Run By Trustees (3) American Spacemodeling M. Bundick Standards and squarely testing J. Kane Nationa...
Just picked it up, I'll try to keep my review brief. Nice, I like the smaller size, as free shelf space tends to shrink over the years. Also, the TOS Enterprise doesn't have a lot of surface detail t
... station. so that any train standing in the station is blocking the points. Is this just an example of space compromise on the model, or was this typical of the prototype? And if so, what would the...
... accidentally clasified as an explosive and is so powefrul that it is negatively used in the bosters for space shuttles. The legislation as originally conceived "will harm homewland security by provid...
....org/~kaplow_r/ www.nira-rocketry.org www.nar.org Save Model Rocketry from the HSA! http://www.space-rockets.com/congress.html...
...erminus on the same level as the rest of the layout. Being 4 to 6 inches lower I will have a little more space under the 2 chimney supporting brackets. I would then run a track down an incline at on e...
... my CD-335 and found that they WOULD NOT FIT! ! ! Why in the heck did the 'expletive deleted' designers space the banana jacks at 15mm, instead of the universal 3/4 inch. Most of my charging cables ...
... 1/32 seems TOO big for me... I like detailing, but maybe I am still just too affraid, or lack the shelf space. I will stick with God's choice, 1/48... were he to want something besides 1:1. Let's no...
...Adbulrahim, James Clifton, Donald MacArthur and Carlo Francis - all students in the Mechanical & Aerospace Engineering Department. Baron now holds the world record for flying the smallest Micro A...
Page: 12

Copyright © 2006 - Jan 2009 Models Buzz