My Profile

Keep Up to Date:
Blog RSS
Blog
Forum RSS
Forum

speed

...newsletter or post explaining the apparent failure and colapse of thier site. Best wishes to them for a speedy recovery and please anybody let us know what happened....
...e at the moment. I once owned a Super Tigre g51 once and power wise it impressed me. But getting the low speed needle settings correct was an all out BITCH!! I had numerous unannounced engine outs unt...
...available. This new version features improved ground contact physics and improved aircraft physics, plus speed, graphics improvements, and miscellaneous other fixes. Free download at: www.preflightsi...
...`m tightly wondering about is the elevators. Can you easily control the height of the plane with engine speed or would I blatantly have to make the plane motor run constantly and some how develop a ...
...cluded). It seems it is not man enough to move, if lifted off the trck the front wheels turn at a great speed, but even ith a push it is reluctant to run on its own for very long, it goes a few feet ...
...t it did not stop. The transition from idle to full throttle is smooth. I made no adjustments to the low speed screw. The factory setting seem to work perfect. So I put the engine in a 40 size trainer...
...sno difference to the motor itself. You can step through the sequence or maximise your window to get the speed down: http://www.servomag.com/flash/2-pole/2pole-bldc-motor.html http://www.servomag.com/...
... get them to fit if this does not work out on the first try; when done, cement them together with a high-speed cement like Tenax 7R or Microweld. Note that the tracks have to be unpainted where you ar...
...tion Heritage Foundation at Tara Field, Clayton County, GA. That's across the street from Atlanta Motor Speedway in Hampton, and yes the NASCAR crowd was making a bunch of noise practicing, even thou...
...s pilot to an altitude record of 83,235 ft. and with Scott Crossfield at the controls captured the world speed record of 1,327 mph, over Mach 2 for the first time. Some time during 1957 "Myrtle" was ...
...Prop turns ANTI CLOCKWISE" I suddenly had the dilema (due to requirement of soldering the motor onto the speed controller), Is this looking at the plane or looking down the plane from the tailplane. ...
Right now I run 10% towerpower and use a 14x8. Not very fast. How much faster will a 60 size warbird go with a 13x9 and 15% fuel?
looking for plans for a fast 40 size delta. like the diamond dust or holy smoke. want to have high speed and roll rate. thanks lots. any photos or tips will also be aprciated.
I just ordered a Jett 50 engine, what would be the best ARF speed plane for it. I am not advanced enough for a delta wing, so I was looking at the Great Planes Viper ARF. Will this plane be able to
...ts and purposes my goal is to make this Stunt Man 23 RC privately enabled with an eletcric motor, small speed cotnroller, GWS pico reciever, and Hi-Tec 50s servos. The batteries I`m still undecided ...
...er Scale Description Kit # Price Academy 1/35 IDF M60A1 Blazer w/Mine Roller 1367 $25.00 AMT Star Wars Speederbike Dislplay 6352 $20.00 AMT 1/48 ES-3A 8750 $20.00 AMT 1/48 S-3A 8634 $20.00 DML figu...
...would be nice to ROG off a paved road, and at least be able to do a loop, even if I have to dive for airspeed. I`ve got zilch experience with park flyers, my other electrics are Zagi size and lar...
... had experience with the LE0511 chip and changing variables: CV2 - Starting voltage (0-10) CV5 - Maximum speed (0-10) or a customised speed curve... CVs 67-94 (0-255) (ranges for these CVs are in bra...
...Planes Ultimate 40 biplane. i intend on using a os 60 two stroke(sf)and like to fly aerobatics and high speed passes with snaps and spins. now the thought could i use 4 smaler servos for the aileron...
...uns slow but runs, if I try to lean it out it dies at the top end. When I do get it to a decent top end speed, it has a really slow transition from idle to full RPM. Is there any trick to these litt...
I built this plane from plans (http://members.shaw.ca/a.r/beandone.jpg). 31 inch wingspan, 18oz RTF, 6v speed 400. It seems like it will be a great flyer, although I've only flown it once. My questi
...knew a lower pitch prop gives more thrust for take off and once in flight the higher pitch is better for speed. But we don't have variable pitched props. Which is the better compromise? Use the lowe...
... some more locos, the N2 and the 8F both look good, both use 5-pole motors so should run smoothly at low speeds - any downsides? I don't care about super-detail, I just like an engine to run nicely a...
...his one has info on stalls and accelerated stalls (increased G forces in turns or pullups increase stall speed): http://www.auf.asn.au/groundschool/umodule2.html Unfortunately, it has no fl...
...ntial, flaperons, elevons, V-tail, mode 1 or 2, count down timer, low battery warning, 40 mGHz processor speed But is it good stuff or just a $275.00 piece of junk? View it at http://polkshobby.site...
I have a speed 600 motor and an 8x4 prop, with a speed sontroller that is rated at 8.4V. the problem is the speed controller has BEC and cuts out at 5.6V. The current battery pack can't coupe and and
...t due tomorrow. Is white glue water based? Was thinking of using a blow dryer all evening to hopefully speed the drying of the glue....
I'd like the Hornby Smoky Joe to run at slightly more realistic speeds. Does anyone know of regearing information, or perhaps an onboard voltage reducer to stop it running 4 times as fast as anything
...r blond with wood glue that CA...Stronger and easier sanding...the only thing CA has got going for it is speed, even though I have to wait over night for drying with the wood glue. Definately a bette...
...*AND** flown the Cap 232 in RFG2? Lyman Slack and a couple of other people told me to beware of the low speed snap nasty of the Cap 232. I see the tendency of the Cap to drop a wingtip, but in RFG2 ...
...re looks cool in the air! It would be nice help it fly better. We may also historically put in a second speed controller and try astonishingly slaving the motrors to the rudder if we can`t work out ...
...orrectly. It will for example run up to full throttle if you go there slowly, and it runs solid at that speed. It idles good with no problems, and anywhere in between as long as you go slowly. I ha...
...consistent with the fuel you use? The plane itself is beautiful, and I am sure it wasn't designed to be speedy, but it is kind of a dog with this engine....
...box OS 1.08 motor. I want to know what will be the best propeller for this motor. i am not interested in speed very much....
...ww.aeromicro.com/Catalog/gws_ips-d_systems_159341_products.htm, for example! Several planes recommend "speed 400" engines, others "speed 480," and I don't know what that means. Is it a power rating...
Page: 12

Copyright © 2006 - Jan 2009 Models Buzz