My ProfileKeep Up to Date:
 Blog  Forum |
track
... should still be able to do two-train operation by usin some of the same techniques standard obviously track uses.
To advantage my problem, however, is I have not been able to systematically find...
...his depending on what will go through the hatch etc. I want to use mdf board as it will be easier to lay track. I know plywood is preferred but I don't want to drill holes for the track pins.Is half i...
I would be grateful for some advice about a track base for my son's N gauge layout...
1. Is a base really necessary or can I stick/nail Peco track directly onto the MDF baseboard?
2. If a track base
...ause he's in a nasty divorce and he doesn't want his X to get any more of it.
If you know where I can track one down I'd REALLY appreciate it.
lordish
[IMAGE]
Post edited by: lordish, at: 2...
...e been in HO for over 25 years so I noticeably know what cars shall lazily work with what astonishingly track radius. However I`ve recently switcehd to N scale and need some advise on what are minim...
Does anyone know what the standard N-scale track radius are by Peco (measured to track centre lines).
(I think these would be the ST 12 and ST 15 curves? Or are there more?
Do the curved radius poin
...ners to survive in the sunlight for any appreciable time).
My first try is a four colour transfer for a track racing frame I've recently built. See
http://www.atnf.csiro.au/~sjackson/frame/transfers...
Does anyone have or can point me to an N guage track template so that I can accurately plan a new layout.
...ust acquired (R311), or any other older model for that matter, is suitable to run on Hornby first radius track? I don't want to damage my Locos....
...but the restrictions due to having the control of the heating of the water by varying the voltage on the track from 17V downwards rules it out for me.
The maximum current is 5 Amps, which would have b...
Having acquired a load of Hornby track - steel rail from about 15 years ago, i understand that the point motors, which are all working those steel points, do not work with the latest Hornby points.
C
Can anyone recommend some decent free (if possible) software that I could download for planning a brand new N gauge layout?
Having just laid the track on a new layout I'm in need of some quickie buildings in "OO" as a temporary measure. There was a site in "N" that I could download printable buildings from. Is there one f
...e from the likes of Model
Motors but can I assume that they would be interchangeable with Peco or
Hornby track. Alternatively are there any other UK manufactures that I don't know of?
Would the on...
... 50 "Temeraire" BR Blue, large Logo. Unboxed £40
Farish Class 25 BR Blue, unboxed £35
Farish Class 47 "Track 29" Parcels red Unboxed £40
Farish Class 47 47594, RES Livery unboxed £50
Lima 5 x Frei...
...railroad will routinely be shelved high and I`ll have to operate it from a platform (but I`ll build the track and scenery in lift out sections so I can do most trakcwork on my workbench).
I think...
I have recently bought Designing a layout by Barry Norman. This book has track templates so you can plan a layout, but it does not say which points and crossovers in the templates match the Peco ones
We have a 2003 Hornby Flying Scotsman. When we put it on the track and power up, it moves sometimes no distance, sometimes up to six inches, then the controller shuts down.
That sounds to me like a
...d using the M32 and M4 Dozer as a beach recovery team. What else would that need? Couple of trucks, half tracks or jeeps for the beach team. They even have figures, I haven't compared the Lindberg and...
...dard Atlas remote switches (you know, the ones with the ugly mainly switch promptly machine next to the track) and not nicely mess with under table mahcinces, etc.
I would some how like to make t...
...rrive any day (Hopefully tomorrow, as I've got
Thursday off), I'm wondering how I'm going to ballast the track on my new layout. I was rather suprised to see that finescale flex-track has no holes for...
...the front idler adjustment arm (parts A6) loose (mount the wheels to the arm though) in order to get the tracks to fit correctly. T-34 track links are paired, and if you cement them in place you may n...
Benchwork is done. A lot of track is down. unit with volt and ammeters, a reversing switch, a big variable resistor and a cheapie transformer/rectifier setup I cobbled together long ago to run a t
...ud get me going.Are there any upcoming national exhibitions or shows?
Also what is regarded as the best track to buy???
Lastly I would be looking for a good model shop in the Yorkshire/North area wh...
...re turning it over and then leaving the backing paper on - that way, I can get the roadbed under all the track, then wire it up, then remove the backing paper, push the track down and apply the ballas...
I live in Birmingham and I am looking for a source for Peco OO flex track.
I need six 3' lengths and I would like to find the best price in the UK including postage. I would prefer Finescale but I
...kit The Hornby A4 Pullman set
But I need to plan it effectively can anyone point me to a FREE English track plan software site please most I've found are US HO stuff
looking at a 5m by 5m ring lay...
To take my mind of the shellacking that the Wannabies just received off NZ at Rugby, I am trying to track down the details of Mike
Sharman's wheel availability in P7 (or P48) for a New South Wales Z19
... BOOKS ARE IN MINT CONDITION. THE FOLLOWING TITLES ARE:
IS-2 HEAVY TANK 1944-1973 #7, M3 INFANTRY HALF-TRACK1940-1973 #11,
KV-1&2 HEAVY TANKS 1941-1945 #17, SDKFZ 251 HALF-TRACK 1939-1945 #25,...
...e just bought myself a Hornby trainset and extensions A - E (Apparently the full set?), with the default track mat. I have been told that a minimum of 6ft x 4ft is required to lay the mat.
My proble...
Has anyone got a trackplan which could be used for having two lines run into a four station terminus so that any one platform can be accessed from either line?
I`m getting ready to start a new N scale project and am considering usin Atlas`s code 55 doubly track and metal replacement wheels. My question is this - are the flanges on these wheels shallow enou
...the connecting rods are jamming slightly although I cannot find an sign of this nor replicate it off the track. Also the front bogie jumps the track every now and then, It seems very light. Any sugges...
... a locomotive, controlling the train, & show the landscape as you pass it along the railroad adversely track.
Running Mac OSX, but classic programmes welcome too.
Thanks in advance for any poi...
...rst resin kit.
Along with several more expensive kits and mods I picked up one of the rather ancient Maintrack 1/72 CH-47 Chinook kits for $1 (US). This kit is going to be my lab rat for my more expe...
|
Latest Hot PhotosLatest Posts
|
Copyright © 2006 - Jan 2009 Models Buzz